 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Next Previous PulseGuard (R) Suppressors Polymeric ESD Suppressors PGB Series 0603 Surface Mount ESD Suppressor Product Overview PulseGuard ESD Suppressors help protect sensitive electronic equipment against electrostatic discharge (ESD). They supplement the on-chip protection of integrated circuitry and are best suited for lowvoltage, high-speed applications where low capacitance is important. Data ports utilizing such high-speed protocols as USB 2.0, IEEE1394 and InfiniBandSM can benefit from this new technology. PulseGuard suppressors use polymer composite materials to suppress fast-rising ESD transients (as specified in IEC 61000-4-2 and MIL-STD-883C). Features * Ultra-low capacitance * Low leakage current * Fast response time * Single line of protection * Bi-directional * Withstands multiple ESD strikes * Standard EIA SOCM-1608 package * Compatible with pick-and-place processes * Available in 1,000 and 5,000 piece reels (EIA-RS481) Physical Specifications Materials: Body: Glass Epoxy Terminations: Tin-Lead Typical Applications * * * * * * Servers Laptop/Desktop Computers Network Hardware Computer Peripherals Digital Cameras External Storage Soldering Parameters: Wave solder -- 260C, 10 seconds maximum Reflow solder -- 260C, 30 seconds maximum Operating Temperature Range: Electrical Characteristics Trigger Voltage1 ...................................................................1,000V, typical Clamping Voltage1 ..................................................................150V, typical Rated Voltage ........................................................................24VDC, max Capacitance2 ................................................................................0.055 pF Response Time1 ...............................................................................< 1 ns Leakage Current3 ..............................................................................< 1nA ESD Pulse Withstand............................................1,000 pulses, minimum NOTES: 1. 8 kV direct discharge method, per IEC 61000-4-2. 2. Measured at 1 MHz. 3. Measured at 6 VDC. Testing at fast ESD pulse rates (1-20Hz) may cause a change in leakage current performance (6A, max). -65C to 125C Ordering Information CATALOG NUMBER PGB0010603MR PGB0010603NR PIECES PER REEL 1,000 5,000 Design Consideration Because of the fast rise-time of the ESD transient, placement of PulseGuard suppressors is a key design consideration. To achieve optimal ESD suppression, the devices should be placed on the circuit board as close to the source of the ESD transient as possible. Install PulseGuard suppressors directly behind the connector so that they are the first board-level circuit component encountered by the ESD transient. They are connected from signal/data line to ground. 174 w w w. l i t t e l f u s e . c o m Next Previous PulseGuard (R) Suppressors Polymeric ESD Suppressors PGB Series 0603 Surface Mount ESD Suppressor Generalized PulseGuard Suppressor Response to ESD (Positive and Negative Polarity ESD Pulses) Trigger Voltage Voltage (V) Generalized I-V Curve (Positive and Negative Polarity ESD Pulses) Trigger Voltage Current (A) Clamping Voltage Clamping Voltage Voltage (V) Time (ns) 4 PULSEGUARD(R) SUPPRESSORS 2.0 Definitions Trigger Voltage: The measured peak voltage across the ESD suppressor before it transitions from high to low resistance. It is manifested as a "spike" before the clamping voltage is achieved. This voltage is typically well below the damage threshold of on-chip IC protection. Clamping Voltage: The voltage level to which the ESD impulse voltage is reduced. This is the voltage that the suppressor holds at, until the ESD transient energy is dissipated. ESD Impulse Voltage: Also known as the ESD Threat Voltage. This is the voltage that is "zapped" into the circuit. Voltages generated by people can exceed 15 kV. The IEC 61000-4-2 defines four levels of impulse voltage for testing purposes: DIRECT DISCHARGE 2 kV 4 kV 6 kV 8 kV Capacitance vs. Frequency ** Note: 1,000 fF = 1 pF 70 Capacitance (fF) 60 50 40 0.5 1.0 1.5 Frequency (GHz) SEVERITY LEVEL 1 2 3 4 AIR DISCHARGE 2 kV 4 kV 8 kV 15 kV Carrier Tape Specifications Parts are delivered on 7" (178mm) reel, paper carrier tape DESCRIPTION Ct - Cover tape thickness MEASUREMENT (MM) 0.06 1.50 4.00 0.58 1.85 4.00 1.02 0.65 8.00 Tt Dd + + Ds + + Dd - Drive hole diameter Ds - Drive hole spacing Pd - Pocket depth Tw Pd + + + + Ph Ph - Pocket height Ps - Pocket spacing Pw - Pocket width Tt - Carrier tape thickness Tw - Carrier tape width Ct Ps Pw w w w. l i t t e l f u s e . c o m 175 Next Previous PulseGuard (R) Suppressors Polymeric ESD Suppressors PGB Series 0603 Surface Mount ESD Suppressor Test Set-up for IEC 61000-4-2 Waveform, 2kV-15kV Device under test Tek P6156 Probe (Voltage measurement) KeyTek pulser 2,000- 15,000 V Brown tip (x100) x10 Faraday cage Ground return x10 Tektronic TDS 684B Blue tip (x10) .5 ohm shunt (10-5 ohms in parallel) Tek P6156 Probe (Current measurement) Reference Schematics: Recommended Pad Layout: Device Dimensions: 1.60 (0.063") Equivalent Circuit: d 0.81 (0.032") 1 2 a b c b a *Dimension 'a' is: 0.457 (.018") *Dimension 'b' is: 0.381 (.015") A SOLDER METHOD Wave Solder Reflow Solder INCH 0.050 0.050 MM 1.27 1.27 INCH 0.030 0.020 B MM .762 .508 INCH 0.130 0.120 C MM 3.30 3.05 INCH 0.030 0.030 D MM .762 .762 NOTE: PulseGuard suppressors are bi-directional; they can be installed regardless of the orientation of their terminals. They have no inherent polarity. 176 w w w. l i t t e l f u s e . c o m |
Price & Availability of PGB0010603MR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |